Selection of ceramic sanitary ware varieties
The main varieties of ceramic sanitary ware are toilets, bidets, facial washers, sinks, mop pools, hand carton boxes, soap boxes, etc. Currently, there are many brands of ceramic sanitary ware on the market, and there are large differences in quality grades, and there is a wide range of price differences. When purchasing, you should first have a sense of support, first determine the standards you expect to reach, and each component or accessory in the kit should be at the same level.
　　 Determine the toilet drainage method and installation size
Before purchasing the toilet, be sure to measure the distance from the center of the outlet to the wall surface (down drainage method) or the distance from the floor surface (post-drainage method) to determine whether the selected toilet is a drainage or rear drainage structure. The method is consistent and the size of the toilet is suitable for installation. The wall spacing of the toilet drain outlet should be equal to or slightly smaller than the wall distance of the toilet outlet (down drainage method); the distance from the toilet drainage outlet to the ground should be equal to or slightly higher than the height of the toilet drainage outlet (after drainage).
　　 Matching product style tone must match
The number of ceramic pieces in the bathroom is more than one, and the number of ceramic products such as toilet bowls, wash basins, soap boxes, hand paper boxes, and mop pools can only be consistent or close to harmony and beauty.
　　 Carefully select the visible surface
The selection of ceramic sanitary ware should have different requirements for the visible surface and the non-visible surface: The visible surface refers to the surface that is easy to see after the porcelain is installed, and the quality of the visible surface should be strictly controlled, especially when the water is splashed when used. The quality of the parts is more important, and the quality of the invisible surfaces after installation should not be too picky.
　　 Three judgments of appearance quality
(1) Whether or not there is cracking: Tap the edge of the porcelain piece with a thin rod to hear its sound crisp, and when there is a "scratching" sound, it proves that there is a crack in the porcelain piece.
(2) Deformation size: Put the porcelain pieces on a flat platform, check whether the movement is smooth and even in all directions, whether the installation surface and the edge of the porcelain surface are flat and whether the installation holes are even and smooth.
(3) Glaze quality: The glaze must be smooth and smooth, and the glaze should be uniform. Visible surface, especially the quality of glazed water splashing is especially important. Drop a few drops of colored liquid on the glaze with a cloth to wipe it evenly. After a few seconds, use a damp cloth to dry it. Check the glaze and no dirty spots are better.
Porcelain pieces also have water absorption. Toilets also have performance requirements such as sewage discharge, water consumption, noise, and water-sealing functions. Consumers of these properties are generally difficult to check and judge, and should be selected as much as possible.
For products purchased with quality credit guarantee, please refer to the recent effective quality inspection report covered by the CMA chapter which has been certified by the relevant national authorities.Bay window decoration entrance decoration style decoration style bathroom door size bathroom size bathroom door
At PFMOLD we can design and produce dies according to your exact specifications or samples. The vast experience of our
engineers allows them to eliminate any potential problems and provide you with high quality Die Casting tooling that can be
used to create superior and efficient die casting products.
Type of the molds:
Lighting Accessories die casting Molds
Kitchen Utensils die casting Molds
Furniture Fittings die casting Molds
Aluminum Heat Sink die casting Molds
Digital die casting Molds
Metal Injection Mold
Mold Standard HASCO, DME, JIS, CHINA LKM
Mold Base LKM & HASCO & DME standard
Material Main Core & Cavity Insert
H13,DIEVAR, 8407, SKD61, 718, S136, 420ESR,NAK80,Hardness of Steel 46~56HRC
Cavity Single-cavity, Multi-cavity
Surface Finish EDM & High Polish
Mold Life Time 50,000shots,1,000,000shots
Applied Software Pro-E, Solid Works, UG, CAD
Quality ISO9001-2008 Certification
Lead-time 4-8weeks
Package Wooden/plywood case for tool
Furniture Fittings Mold,Furniture Fittings Mold, Plastic Mould
PF Mold Co., Ltd. , http://www.pf-mold.com