Solid wood composite flooring is made of staggered laminates of different tree species, to a certain extent overcome the shortcomings of solid wood flooring, wet swelling and shrinkage, dry shrinkage, low swelling rate, good dimensional stability, and retained the solid wood floor Natural wood grain and comfortable feet. Solid wood composite flooring combines the stability of laminate flooring with the beauty of solid wood flooring, and it also has environmental advantages. So, do you know how to lay parquet ? “Three-point floor, seven-point installation†shows how important the floor installation is. However, many owners disregard the importance of floor installation and lead to various unnecessary troubles after floor installation. How does the solid wood laminate flooring and parquet require keeling? May wish to follow me to learn about it!
First, the eight shopping standards of solid wood flooring
1, see the release of formaldehyde
Formaldehyde emission is one of the indicators for the purchase of wooden floors, and it is also the most critical point! This mainly depends on whether its formaldehyde limit has reached the national target. General formaldehyde limit is divided into three levels: EO <= 0.5mg / l, E1 <= 1.5mg / l, E2 <= 5mg / l; According to the new regulations issued by China's Health and Environmental Protection Agency, where formaldehyde content of solid wood flooring reaches E2 Even if qualified. To achieve EO, E1 standard materials can be directly used for interior decoration, be considered environmentally safe floor!
2, see the origin of raw materials
The performance of solid wood flooring is determined by its wood species. Floors made of stable wood naturally have much more stability. Nine positive home network suggested that we should choose the best when the tree species are better, generally better wood is rosewood, teak, eucalyptus and so on. In general, imported raw materials are better than domestic ones!
3, test moisture content
The moisture content of solid wood flooring should be chosen to be equal to the residential installation area, which will greatly reduce the possibility of problems in future use. National standards stipulate that the moisture content of wood floors is 8% to 13%. In fact, our country has a vast territory and different regions have different moisture content requirements. At the time of purchase, the moisture content of the wooden floor selected in the exhibition hall shall be measured first, and then the moisture content of the wooden flooring of the same species and the same specifications of the unopened packaging shall be measured. If the difference is +2%, the moisture content may be regarded as qualified.
4, the size of the size
Determine the appropriate length, width, solid wood flooring is not the longer the longer the better, the length, width of the wood floor is relatively easy to deform. Try to choose the plate, length 450---910mm, width 90---125mm. Below this standard is non-standard. Many people think that the smaller the floor, the better the stability, and the truth is right. However, due to the fact that many non-standard plates are made of non-trunks, the stability will be greatly reduced.
5, check the quality of the board
The quality of the board is one of the main basis for the floor classification. First check whether the same species, whether mixed species, whether the floor dead, live, cracking, decay, bacteria and other defects. Then observe the accuracy of the wooden floor, after the general wood floor can be removed out of the box about 10 freehand assembly, observe the enterprise mouth bite, assembly gap, the difference between the adjacent plate height, if the strict joint, feel no significant height difference. If there are chromatic aberrations, knots, textures, etc. consumers can ignore, because these things natural properties of wood, showing the natural qualities of solid wood flooring.
6, see the quality of auxiliary materials
The quality of the auxiliary material directly affects the installation and service life of the floor. Therefore, the price and quality of skirting boards and beading are also issues that consumers need to be concerned about. In the past, the baseboards of the laminate floorings were mostly wooden baseboards, which were not only easily deformed but also brought about problems of formaldehyde pollution. The latest technology on the market is the new baseboard produced by the American polymer foaming technology. The formaldehyde emission from the baseboard of this material is almost zero. At the same time, it is also wear-resistant, fire-retardant, mold-proof, anti-static, etc. Advantages, and strong toughness and moldability, ideal for special units and arc wall decoration.
7, see the paint quality and paint process
After the board is painted, it is called lacquer board. The quality of the board surface and finish are selected. The key is to see the finish of the paint film, no air bubbles, paint leakage, and wear resistance. The surface is even and smooth, no bubbles, no cracks and no paint leakage.
8, the priority of high quality after-sales service
There is a saying in the flooring industry: “Three floors, seven pavingsâ€. It can be seen that the floor installation has an impact on the quality of floor use. Therefore, consumers must pay attention to selecting the manufacturers who have high-quality after-sales services to install the floor. Before the installation, we must sign the installation agreement. In the agreement, if there is a problem with the solid wood floor, in the end who will be responsible for it, this can prevent the manufacturers from escaping the responsibility and repair the local board in time if there is a problem.
Second, solid wood flooring how to shop
1, before the solid wood composite floor pavement six shop
(1) The floor is not dry (wet), not clean
(2) Termites in the surrounding environment
(3) Cross-mixing operations at the construction site
(4) Use inferior, polluted, moist, and decaying materials as keels
(5) The construction period is too short to implement the process
(6) Absolute flatness without color difference
2, solid wood composite floor pavement process
(1) In order to make the interface between the two floors more secure and not loose, apply a special fixing glue on the horizontal and vertical interfaces of the floor before installation.
(2) Strike the floor from the side to make the interface of the floor better fixed. At this time, the surface joints of the floor will be thinner and invisible. When installing and splicing floors, pay attention to the width of the gap around the floor and walls.
(3) Using special tools to tightly bond the floor, the gap between the floor and the wall can maintain the specified 8-10mm. When installing the floor, in order to maintain a fixed expansion joint with the wall, a small wooden block of this thickness can be used to cover the floor.
(4) Even for irregular corners, the expansion joints on the floor and wall must be kept very well, which can reflect the construction quality. The upper part of the buckle, in order to fix the buckle, but also for the appearance of the appearance, in fact, have to install another part of the buckle.
(5) Use pliers to press the gap of the buckle, the upper and lower parts will be more stable and more secure, or else there will be sound when stepping on. To fasten the buckles to the previously installed buckles, the top and bottom buckles must be fastened and no sound can be heard. If the gap between the floor and the closet cannot be covered by the baseboard, then it should be sealed with PVC material.
(6) In this case, solid wood flooring is basically installed. Next, it is the responsible company that does the necessary finishing work.
3, acceptance after solid wood composite floor pavement
After the installation of the floor is usually accepted within 3 days
The floor surface should be clean and flat. The quality of the floor appearance meets the requirements of the corresponding product standards.
Patchwork is 1/2 or 1/3 of the length of the adjacent row of floor boards.
Laying the floor should be firm, not loose, stampede no abnormal sound.
After paving solid wood flooring, you must use it for at least 24 hours before you use it, otherwise it will affect the use of parquet. The poor water resistance of general solid wood flooring should not be wiped with a damp cloth or water to avoid losing luster. Usually experienced after the test of temperature changes in the four seasons, the floor will be more and more stable, focus on daily maintenance will be able to extend the service life and improve the use of results.
Solid wood laminate flooring can be laid directly on a flat, dry floor for its special product structure. In particular, cities in the north are almost always paved, including floors with floor heating systems.
Different users have their own consumption habits, and most of them have hit the keel. It is best to encrypt the keel when playing, to ensure the sense of foot but also to ensure the strength of the force, the cost is naturally higher than the cement leveling. However, experts at the flooring experts recommend that everyone put the keel in the best way. When the keel is laid, there is a certain distance between the keels. When the talents are between the keel, there will be floor deflection, so when the elastic modulus of the solid wood flooring and the static bending strength are small, the foot will appear soft. feel.
Third, solid wood flooring laying notes:
1. The short joints between the floorboards must be staggered by at least 20cm, so that the paved floorboards will be more robust, stable, and reduce waste and enhance the overall effect, but the long-edge joints between the rows must be kept in line, so the first A row of flats that are not against the wall.
2. When laying floors, against the wall, stairs, columns, pipes or other hard facades, we must reserve 8mm ~ 12mm of the gap, the area south of the Yangtze River proposed more than 10mm in the doorway, angled room.
3. When the room is longer than 8m (at the end of the floor block) and is wider than 8m (the floor is cross-paved), a gap of 1:1 is required in advance. Void joints are covered with grommets. If the length or width exceeds 8m, the slats must be added and the expansion joints must be left. The pinch plate screws must not be fixed too tightly. Too tight the floor cannot float, and it is easy to press the floor block.
4. When laying, not only the floor should be left with contraction joints, but also the floor mats should be left with contraction joints.
5. The short head under the previous row of floor saws is less than 30cm, and the new floor is used directly. The last floor should not be shorter than 5cm.
6. When the mouth is used with glue, 0.5l can be used for about 12m2 to 15m2 floor outlets. When the floor of each floor is fully filled with tongue-in-mouth glue, when the floor is put together, a small string of glue appears on the joints (with a cloth Wipe away in time. Only with proper adhesive, the floor can withstand vibration and water erosion.
7. The glue residue can be removed with a household cleaner or lightly shaved with a thin sheet.
Edit Summary: The above is how laying parquet, parquet flooring and precautions related presentations, in the decoration of houses, floor installation, good or bad, will directly affect the floor's appearance and longevity. Therefore, when installing the floor, be sure to choose professional personnel to install. For more information, please continue to follow our website.
Parquet
Insect Killer Lamp,Bl Tube,Bl Lamp,Bl Bulb
Changxing leboom lighting product CO.Ltd. , https://www.leboomuvd.com